Dealing with a garage door that needs a repair service can be a frustrating experience. That why we are committed to exceeding your garage door repair service in Naperville, IL expectations. Our reputation is built from thousands of satisfied customers over the past 30 plus years in the Western Suburbs of Chicago. Whether it is a broken spring, or a garage door opener that need a repair, make us your first call in Naperville, IL.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.

Does your garage door squeak or make a lot of noise when opening? There are some specific ways to help reduce the squeaking of your garage door. Many people will lubricate everything, but that actually can cause damage and a huge mess. There are some specific things that you can lubricate to help maintain the life of your garage door and reduce noise levels. This video explains how to lubricate your garage door to reduce noise and increase the life of your garage door.
I see the ovens next to 'fridge. Isn't that a no-no? The heat from the ovens make the 'fridge run to cool more when the ovens are used, upping the electric bill. They are also too far from the center of preparation. I would have put them against the long counter. It would also allow counter space by the fridge to place items when putting them in or taking them out of the 'fridge.

When the lay-person typically sees a circuit board, they immediately seize up and think that's it's too advanced for them to fix. In reality, replacing circuit boards for the Chamberlain Liftmaster, Sears, and Craftsman garage door openers is relatively easy with proper instruction. This video will walk you through the process of replacing the circuit board on a Chamberlain Liftmaster, Sears, and Craftsman garage door opener.


In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.

LED & Florescent lights: I hear you asking “why is this important?”. Both can emit radio and electromagnetic interference that can mask the signal between the smart hub and your opener. If you experience unreliable operation - out they go. The last thing I did was remove an LED lamp from a motion sensor fixture nearby and replaced it with a standard incandescent. Since the light is only on for a few minutes I’m not worried about the power usage if it means the garage door will close when commanded. Click Here for Garage Door Repairs
Now check the springs. There will be just one on a single-car garage, two on a two-car garage. Roll-up doors are operated by torsion springs, controlled by cables on pulleys. Two-car models can be adjusted by pulling the cable further through the plate above the door, then knotting the end to hold the newly established tension. One-car roll-up door springs should only be adjusted by a professional, as there is such a great amount of tension on the one spring that you could be injured when trying to adjust it yourself. Swing-up door springs are hooked on each side of the door into special notches or holes. To adjust the tension on these springs, simply move the spring hooks to the next notch. 

Garage Door Opener Co

×